Switch Quality

Projekte

L2-Switch; LevelOne GES-2450; voller Sicherheitslücken (Start here); RTL8389LM; Bluetooth Enabled mit HC-06-Modul

Console

TTL-UART 3.3V; Bluetooth Device Name: GES-2450

CPU: MIPS 4KEc 300 MHz, id: 0x90, rev: 0x6c
Peripheral: 200 MHz
DRAM:  32 MB
Probe: SPI CS0 Flash Type S25FL064A
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Switch Model: RTL8389LM_8218_DEMO (Port Count: 28)
Switch Chip: RTL8389LM
[DBG] ### Reset PHY through GPIOC pin 1 (RTL8389L/RTL8389LM) ###
### RTL8218 config - PhyIdMask = 0x000000ff ###
### RTL8218 config - PhyIdMask = 0x0000ff00 ###
### RTL8218 config - PhyIdMask = 0x00ff0000 ###
Net:   rtl8389#0
Press space to abort autoboot in 1 second
RTL8389 # help
?       - alias for 'help'
base    - print or set address offset
boardid  - Get/Set board model id
bootm   - boot application image from memory
bootp	- boot image via network using BootP/TFTP protocol
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
erase   - erase FLASH memory
flinfo  - print FLASH memory information
go      - start application at address 'addr'
help    - print online help
iminfo  - print header information for application image
loadb   - load binary file over serial line (kermit mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
md      - memory display
mm      - memory modify (auto-incrementing)
mtest   - simple RAM test
mtest_dtr   - DRAM persistance test.
mw      - memory write (fill)
nm      - memory modify (constant address)
ping	- send ICMP ECHO_REQUEST to network host
printenv- print environment variables
printsys - print system information variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
rtk     - Realtek commands
saveenv - save environment variables to persistent storage
savesys - save system information variables to persistent storage
setenv  - set environment variables
setsys  - set system information variables
tftpboot- boot image via network using TFTP protocol
version - print monitor version

## Booting image at bd160000 ...
   Image Name:   Linux Kernel Image
   Created:      2012-04-20   7:58:02 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    4029188 Bytes =  3.8 MB
   Load Address: 80000000
   Entry Point:  80269000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.19 (root@netronix-desktop) (gcc version 3.4.4 mipssde-6.03.00-20051020) #73 PREEMPT Fri Apr 20 15:57:58 CST 2012
CPU revision is: 0001906c
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 8128
Kernel command line: console=ttyS0,115200 mem=32M
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 26920k/32768k available (2048k kernel code, 5848k reserved, 415k data, 3016k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
NET: Registered protocol family 16
NET: Registered protocol family 2
IP route cache hash table entries: 256 (order: -2, 1024 bytes)
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 1024 bind 512)
TCP reno registered
squashfs: version 3.3 (2007/10/31) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 31) is a 16550A
loop: loaded (max 8 devices)
Probe: SPI CS1 Flash Type S25FL064A
Unknown SPI CS2 Flash ID=0xffffffff.
Creating 5 MTD partitions on "Total SPI FLASH":
0x00000000-0x00040000 : "LOADER"
0x00040000-0x00050000 : "BDINFO"
0x00050000-0x00060000 : "SYSINFO"
0x00060000-0x00160000 : "JFFS2"
0x00160000-0x00800000 : "RUNTIME"
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Freeing unused kernel memory: 3016k freed
SQUASHFS: Mounting a different endian SQUASHFS filesystem on loop0
SQUASHFS: Mounting a different endian SQUASHFS filesystem on loop1
rtcore: module license 'unspecified' taints kernel.
Init RTCORE Driver Module....OK
Init SYS NIC Driver Module....OK
Init RTK Driver Module....OK
Init RTDRV Driver Module....OK
Init Board Configuration Module....OK
Init SKI Core Driver Module....OK
Init VLAN Aware Module....OK
Init Board Core Module....OK
Init Switch L2Glue Module....OK
Init Switch STP Module....OK
Init Switch LACP Module....OK
Init Switch IGMP Snooping Module....OK
Init Switch 802.1X Module....OK
Init Custom Module....OK

====== Defaults Initial [Start] ======
Init Switch Factory Default....OK
Init VLAN Factory Default....OK
Init SVLAN Factory Default....OK
Init Mirror Factory Default....OK
Init L2 Factory Default....OK
Init Trunk Factory Default....OK
Init Rate Factory Default....OK
Init QoS Factory Default....OK
Init LACP Factory Default....OK
Init 802.1x Factory Default....OK
Init IGMP Factory Default....OK
Init STP Factory Default....OK
Init System Factory Default....OK
Init SNMP Factory Default....OK
Init Port Factory Default....OK
Init Syslog Factory Default....OK
Init Custom Factory Default....OK
====== Defaults Initial [Done] ======

====== Initial from startup-config [Start] ======
====== Initial from startup-config [Done] ======

====== Post Initial [Start] ======
Port Post Initial....OK
====== Post Initial [Done] ======

Switch Command Line Interface (version 1.2.3)


Press any key to continue

quality(config)# show version
LevelOne v1.2.3 (quality)
Copyright (C) 2011 Digital Data Communications Asia Co., Ltd.
quality(config)# show running-config
! System Description: LevelOne 24Copper_4Combo Switch